NACE-CIP1-001 Dumps Special Discount for limited time Try FOR FREE
NACE-CIP1-001 Dumps for success in Actual Exam Jul-2024]
NEW QUESTION # 51
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. Low Surface Temperature
- B. High Relative Humidity
- C. High Surface Temperature
- D. Low Relative Humidity
Answer: D
NEW QUESTION # 52
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 75 Gauge Readings resulting in 25 Spot Measurements
- B. 45 Gauge readings resulting in 15 Spot Measurements
- C. 225 Gauge Readings resulting in 75 Spot Measurements
- D. 105 Gauge Readings resulting in 35 Spot Measurements
Answer: C
NEW QUESTION # 53
Most industrial coatings are:
- A. Resistant to concentrated sulfuric acid
- B. Resistant to temperatures above 200C
- C. Organic
- D. Inorganic
Answer: C
NEW QUESTION # 54
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. It depends on which power tool the Contractor selects
- B. No, because there is no real difference in the standards
- C. Yes, because the 'two standards are not equivalent
- D. It depends on which hand tool the Contractor selects
Answer: B
NEW QUESTION # 55
To be of value the Inspector's documentation must be:
- A. Always handwritten
- B. Always typewritten
- C. Submitted before the end of the job
- D. Timely, accurate and concise
Answer: D
NEW QUESTION # 56
Relative humidity is
- A. the highest temperature at which moisture forms on a steel surface.
- B. a measure of the amount of moisture in the air compared to saturation level.
- C. a measure of the amount of moisture in the air compared to the air temperature.
- D. the lowest temperature at which moisture forms on a steel surface.
Answer: B
NEW QUESTION # 57
Conventional spray is a good choice when:
- A. High production rates are required
- B. High viscosity coatings are being applied
- C. High transfer efficiency is required
- D. High quality finishes are required
Answer: D
NEW QUESTION # 58
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Permit coating to take place so as not to lose the blast
- C. Shut the job down
- D. Review the relevant standard with the Contractor
Answer: D
NEW QUESTION # 59
It is good practice for the NACE Inspector to have instrument calibration certificates available:
- A. At all times
- B. In the field only
- C. In the office only
- D. Only if the specification requires it
Answer: A
NEW QUESTION # 60
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Assume the role of the Safety Inspector
- B. Check the PPE used by the Applicators
- C. Check the credentials of the Safety Officer on site
- D. Act in accordance with the site safety requirements and set an example
Answer: D
NEW QUESTION # 61
A successful coating inspector must be able to
- A. look for problems or issues during application.
- B. recommend the appropriate coating technique for the job to the contractor.
- C. advise the coating applicator on how to mix the coating.
- D. apply the coating with expert accuracy.
Answer: A
NEW QUESTION # 62
Solvents are added to coating formulations to
- A. dissolve binders and form liquid coatings.
- B. provide color.
- C. decrease film permeability.
- D. increase film permeability.
Answer: A
NEW QUESTION # 63
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 1
- B. Level 2
- C. Level 4
- D. Level 3
Answer: D
NEW QUESTION # 64
Digital hygrometers
- A. determine relative humidity, air temperature, and dew point temperature:
- B. use a thermocouple in contact with the surface to measure temperature
- C. consist of a bimetallic sensing element protected from wind gusts.
- D. are used to measure temperature from a distance.
Answer: A
NEW QUESTION # 65
Which one of these elements is not necessary for corrosion to occur:
- A. Reference Cell
- B. Anode
- C. Electrolyte
- D. Cathode
Answer: A
NEW QUESTION # 66
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
Answer: A
NEW QUESTION # 67
......
Accurate NACE-CIP1-001 Answers 365 Days Free Updates: https://validexam.pass4cram.com/NACE-CIP1-001-dumps-torrent.html